telephone: 814-362-5536 fax: 814-362-8883 70 speer electronics, inc. mul ti la yer ferrite induct ors monolithic structure for closed magnetic path elimates crosstalk and provides high reliability in a wide range of temperature and humidity ranges standard eia packages: 0603, 0805, 1206 nickel barrier with solder overcoat for excellent soderability magnetically shielded type l w h p 0603 0.063 0.006 0.031 0.006 0.031 0.006 0.014 0.006 (1.600.15) (0.80)0.15) (0.800.15) (0.360.15) 0805 0.079 0.008 0.049 0.008 0.035 0.008 0.020 0.0100 (2.00 0.20) (1.25 0.20) (0.90 0.20) (0.51 0.25) 1206 0.126 0.008 0.063 0.010 0.043 0.008 0.020 0.010 (3.20 0.20) (1.60 0.20) (1.10+0.20) (0.51 0.25) *please note: kse s part numbers do not contain any spaces or hyphens. multilayer ferrite mci inductor ordering & specifying informa tion* mci 0603 h te r10 j t ype size code material packaging nominal t olerance inductance 0603 permability te: 7?embossed plastic j: 5% 0805 code: ted: 13: embossed k: 10% 1206 h plastic 047=0.04 h m: 20% j none: bulk r10=0.100 h dimensions [in (mm)] chip inductors
telephone: 814-362-5536 fax: 814-362-8883 71 speer electronics, inc. multilayer ferrite mci inductor ind. l( h) st andard applica tions continued -25? to 85? te: embossed plastic *add tolerance character (j,k,m) other values available upon request lq test s.r.f. dc. allowable operating type min frequency mhz res dc current temp q (mhz) type (max.) ? max. (ma) mci0603hte047*` 0.047 10 50 260 0.30 50 mci0603hte068* 0.068 10 50 250 0.30 50 mci0603hte082* 0.082 10 50 245 0.30 50 mci0603hter10* 0.10 15 25 240 0.50 50 mci0603hter12* 0.12 15 25 205 0.50 50 mci0603hter15* 0.15 15 25 180 0.60 50 mci0603hter18* 0.18 15 25 165 0.60 50 mci0603hter22* 0.22 15 25 150 0.80 50 mci0603hter27* 0.27 15 25 136 0.80 50 mci0603hter33* 0.33 15 25 125 0.85 35 mci0603hter39* 0.39 15 25 110 1.00 35 mci0603hter47* 0.47 15 25 105 1.35 35 mci0603hter56* 0.56 15 25 95 1.55 35 mci0603hter68* 0.68 15 25 90 1.70 35 mci0603hter82* 0.82 15 25 85 2.10 35 mci0603jte1r0* 1.0 45 10 75 0.40 100 mci0603jte1r2* 1.2 45 10 65 0.50 100 mci0603jte1r5* 1.5 45 10 60 0.50 50 mci0603jte1r8* 1.8 45 10 55 0.50 50 mci0603jte2r2* 2.2 45 10 50 0.60 50 mci0603jte2r7* 2.7 45 10 45 0.60 50 mci0603jte3r3* 3.3 45 10 41 0.70 50 mci0603jte3r9* 3.9 45 10 38 0.80 50 mci0603jte4r7* 4.7 45 10 35 0.90 50 mci0805hte047* 0.047 15 50 320 0.20 300 mci0805hte068* 0.068 15 50 280 0.20 300 mci0805hte082* 0.082 15 50 255 0.20 300 mci0805hter10* 0.10 20 25 235 0.30 250 mci0805hter12* 0.12 20 25 220 0.30 250 mci0805hter15* 0.15 20 25 200 0.40 250 mci0805hter18* 0.18 20 25 185 0.40 250 mci0805hter22* 0.22 20 25 170 0.50 250 mci0805hter27* 0.27 20 25 150 0.50 250 mci0805hter33* 0.33 20 25 145 0.56 250 mci0805hter39* 0.39 25 25 135 0.65 200 mci0805hter47* 0.47 25 25 125 0.65 200 mci0805hter56* 0.56 25 25 115 0.75 150 mci0805hter68* 0.68 25 25 105 0.80 150 mci0805hter82* 0.82 25 25 100 1.00 150 mci0805jte1r6* 1.0 45 10 75 0.40 50 mci0805jte1r2* 1.2 45 10 65 0.50 50 mci0805jte1r5* 1.5 45 10 60 0.50 50 mci0805jte1r8* 1.8 45 10 55 0.50 50 mci0805jte2r2* 2.2 45 10 50 0.65 30 mci0805jte2r7* 2.7 45 10 45 0.75 30 mci0805jte3r3* 3.3 45 10 41 0.80 30 mci0805jte3r9* 3.9 45 10 38 0.90 30 mci0805jte4r7* 4.7 45 10 35 1.00 30 mci0805jte10r* 10 50 2 24 1.15 15 mci0805jte12r* 12 50 2 22 1.25 15 mci1206hte047* 0.047 20 50 320 0.15 300 mci1206hte068* 0.068 20 50 280 0.25 300 mci1206hter10* 0.10 20 25 235 0.25 250 chip inductors
telephone: 814-362-5536 fax: 814-362-8883 72 speer electronics, inc. mci1206hter12* 0.12 20 25 220 0.30 250 mci1206hter15* 0.15 20 25 200 0.30 250 mci1206hter18* 0.18 20 25 185 0.40 250 mci1206hter22* 0.22 20 25 170 0.40 250 mci1206hter27* 0.27 20 25 150 0.50 250 mci1206hter33* 0.33 20 25 145 0.60 250 mci1206hter39* 0.39 25 25 135 0.50 200 mci1206hter47* 0.47 25 25 125 0.60 200 mci1206hter56* 0.56 25 25 115 0.70 150 mci1206hter68* 0.68 25 25 105 0.80 150 mci1206hter82* 0.82 25 25 100 0.90 150 mci1206jte1r0* 1.0 45 10 75 0.40 100 mci1206jte1r2* 1.2 45 10 65 0.50 100 mci1206jte1r5* 1.5 45 10 60 0.50 50 mci1206jte1r8* 1.8 45 10 55 0.50 50 mci1206jte2r2* 2.2 45 10 50 0.60 50 mci1206jte2r7* 2.7 45 10 45 0.60 50 mci1206jte3r3* 3.3 45 10 41 0.70 50 mci1206jte3r9* 3.9 45 10 38 0.80 50 mci1206jte4r7* 4.7 45 10 35 0.90 50 mci1206jte5r6* 5.6 45 4 32 0.9 25 mci1206jte6r8* 6.8 45 4 29 0.9 25 mci1206jte10r* 10 45 2 24 1.0 25 te: embossed plastic *add tolerance character (j,k,m) other values available upon request multilayer ferrite mci inductor ind. l( h) st andard applica tions continued -25? to 85? lq test s.r.f. dc. allowable operating type min frequency mhz res dc current temp q (mhz) type (max.) ? max. (ma) te: embossed plastic *add tolerance character (j,k,m) other values available upon request chip inductors
telephone: 814-362-5536 fax: 814-362-8883 76 speer electronics, inc. parameter requirement test method operating temperature -55 0 c+125 0 c storage temperature 40 0 c @ 70% humidity. sealed plastic bags withdesiccant shall be used to reduce the potential of oxidation on the terminations dur- ing storage resistance to change in impedance: relative flux: 5-10 sec dip to value before test 20%. after flux: air dry for 15 sec preheat: 1 50 0 c 1 0? preheat time: 60 sec solder temp: 260? 5? dip time: 10 1 sec solderability solder coverage: more than 95% of the termination shall be covered with solder. leach resistance appearance: there shall be no visible signs of physical or mechanical damage (i.e. no cracks). terminations: termination must not be leached away for more than 5%. insulation resistance insulation resistance: mm 1g ohms solvent resistance change in impedance: relative to value cleaning by: before test 10%. washer: ultrasonic washer (100w) solvent: isopropyl alcohol time: 3 minutes terminal strength appearance: the terminal electrode shall not (hanging test) break off, nor shall there be damage to the body. type w(kgf) time 0402 na 0603 0.5 30 sec 2 sec 0805 1 .0 30 sec 2 sec 1206 1.5 30 sec 2sec terminal strength appearance : there shall be no evidence of (push test) mechanical degradations to terminals or body. environment al & mechanical characteristics flux: 5-10 sec dip after flux: air dry for 15 sec solder temp: 245? 5 0 c dip time: 5 0.5 sec multilayer ferrite mcb/mcp/mci/mhi inductor appearance: there shall be no cracking solder coverage: more than 75% of the terminal electrode shall be covered with solder. the bead shall be subjected to the following 5 steps for the period of time shown below. the 5 steps constitute one (1) rotation. 4 rotations shall be carried out. 1) flux: 5-10 sec 2) after flux: air dry for 15 sec 3) solder temp: 230? 5? 4) dip time: 5 0.5 sec 5 )cool: air cool for 60 seconds type w(kgf) time 0402 na 0603 1.4 60 sec 0805 1.8 60 sec 1206 2.3 60 sec solder heat chip inductors
telephone: 814-362-5536 fax: 814-362-8883 77 speer electronics, inc. multilayer ferrite mcb/mcp/mci/mhi inductor item requirement conditions bending strength appearance: there shall be no physical or mechanical damage. impedance: relative to initial value before test 10% mechanical shock appearance: there shall be no physical or force: 5oc time: 11 msec there shall be 3 shocks in each of - 6 directions (18 shocks total).me vibration impedance: relative to initial value 10%. only endurance conditioning by sweeping shall be made. the entire frequency range from 10-2,000hz return to10hz in 20 minutes (this shall constitute one cycle). amplitude:1.5mm the test shall have a 1 sc peak and shall be applied for a period of 4 hours (12 cycles) in each of 3 m mutually perpendicular directions (a t total of 36 cycles within a total of 12 hours). thermal shock appearance: there shall be no physical or mechanical damage. impedance: relative to initial value 20%. dcr: the dor shall not exceed initial specified value. testing of the parts will be made at 0 hours, 250 hours and 500 hours. before testing, t he parts shall be allowed to cool to room temperature for 24 hours. load humidity appearance: there shall be no physical or mechanical damage. impedance: relative to initial value 15%. measurements shall be taken at 0 hours, 250 hours, 500 hours and 1,000 hours and shall meet the conditions stated above. life test appearance: there shall be no physical or mechanical damage impedance: relative to initial value 15% measurements shall be taken at 0 hours, 250 hours, 5oo hours and 1,000 hours and shall meet the conditions stated above. environment al & mechanical characteristics board: 90x40x1 .6mm bend: 1mm time: 5 sec mechanical damage. impedance: relative to initial value before test 10% ` step temperature time 1-start -40? 200 2-hold -40? 200 30 mm 5 mm 3-transfer 0.5 mm max. 4-hold +1050? 200 30 mm 5 mm 5-transfer 0.5 mm max. steps 1 thru 5 constitute one complete cycle and the test shall consist of a total of 500 cycles. temperature: 85? 200 relative humidity: 85% time: 1,000 hours total apply: 1 oo%rated current temperature: 85? 2? time: 1,000 hours total apply: 100% rated current chip inductors
|
